Visiting us from ?
UniFi
UISP
Elevator Starter Kit
UA-SK-Elevator
Connects to in-elevator readers using PoE to authorize user's floor selection. Support for up to 18 floors and digital inputs for car status and emergency.

(1) Elevator Hub

(1) G2 Reader

(2) 2-wire PoE extenders

(10) Access Cards

Access Card
د.إ.‏ 146.00
Mission Critical
Installation Guide
Technical Specifications
UA-Hub-Elevator
Mechanical
Dimensions129.3 x 244.7 x 33.6 mm (5.1 x 9.6 x 1.3")
Weight537 g (1.2 lb)
Enclosure materialPolycarbonate
Mounting materialPolycarbonate
Hardware
Networking interface(4) 10/100/1000 Base-T
Management interface(1) 10/100/1000 Base-T
Power methodPoE++
Max. power consumption7W (Without PoE output)
PoE input(1) PoE++, 50V DC, 1.2A
PoE outputPoE passthrough, (4) PoE, 50V DC, total 42W
ESD/EMP protectionAir: ±8kV, contact: ±4kV
Digital input(5) Car position
(6) Car status; Up/down/stop/full/door open/door close
(1) Emergency
Outputs(18) Relays
Rating 30V DC/2A
LEDsSystem: white/blue/red
Output relays: white
Buttons(1) Factory-reset
Terminal blocks
Operating temperature-10 to 40° C (14 to 104° F)
Operating humidity5 to 95% noncondensing
CertificationsCE, FCC, IC
UACC-Extender-2Wire-Tx/Rx
Mechanical
Dimensions40 x 105 x 25 mm (1.6 x 4.1 x 1")
WeightPoE in: 77 g (2.7 oz)
PoE out: 79 g (2.8 oz)
Enclosure materialPolycarbonate
Mounting materialPolycarbonate
Hardware
Networking interface(1) 10/100 MbE
(1) Homeplug AV
Management interface(1) 10/100 MbE
Power methodPoE++
Max. power consumption3W (Without PoE output)
PoE input(1) PoE++, 50V DC, Max. 1.2A
PoE output(1) PoE+, 48V DC, 0.72A
ESD/EMP protectionAir: ±8kV, contact: ±4kV
LEDWhite
Operating temperature-10 to 40° C (14 to 104° F)
Operating humidity5 to 95% noncondensing
CertificationsCE, FCC, IC
UA-G2
Mechanical
Dimensions93 x 40 x 36.5 mm (3.7 x 1.6 x 1.4")
Weight82 g (2.9 oz)
Enclosure materialPolycarbonate, glass
MountingIn wall, gang box
WeatherproofingIP55
Hardware
Networking interface(1) 10/100 MbE RJ45 port
ConnectivityBLE 4.1
Power methodPoE
UL 294 Power-limited Class 2 PSU
UL 60950-1/62368-1 LPS/PS2 PSU
Supported voltage range48V DC
Max. power consumption5W
ESD/EMP protectionAir: ±15kV, contact: ±8kV
SensorsProximity sensor
Speaker(1) 8 ohm, 0.7W
LEDsR/G/B/W
Button(1) Factory-reset
NFC frequency13.56 MHz
NFC read range< 30 mm
NFC standardsISO 14443A, 14443B, 15693
NFC technologyNFC Tag 1,2,3,4,5
MIFARE Classic
MIFAREPlus
MIFARE Ultralight
MIFARE DESFire
Operating environmentOutdoor use
Operating temperature-30 to 45° C (-22 to 113° F)
Operating humidity5 to 90% noncondensing
Software informationThe software version of a product can be checked at https://unifi.ui.com
UL 294 levelDestructive attack: Level I
Line security: Level I
Endurance: Level I
Standby power: Level I
UL 294 statementCompliance with IEEE 802.3 specifications was not verified as part of UL 294.
The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
PoE cabling requirementsCable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm2) for patch cords; 24 AWG (0.21 mm2) for horizontal or riser cable.
CAN/ULC-60839-11-1 GradeGrade assignment: I
CertificationsCE, FCC, IC, UL 294, CAN/ULC-60839-11-1
Document number, and issue date and/or revision levelUA-G2/UA-G2-Black, V02
LED
SystemSteady blue: Adopted/device is ready
Steady white: Pending adoption
Blinking white/blue: Upgrading firmware
Strobing red: Emergency lockdown
UA-Card
Mechanical
Dimensions85.6 x 54 x 0.8 mm (3.4 x 2.1 x 0.03")
Weight5 g (0.18 oz)
FormatISO 7810 ID-1
NFC frequency13.56 MHz
NFC technologyISO/IEC 14443 Type A
MIFARE DESFire
UniFi Access Proprietary Security Protocol